World Library  
Flag as Inappropriate
Email this Article

Water injection (oil production)

Article Id: WHEBN0000980309
Reproduction Date:

Title: Water injection (oil production)  
Author: World Heritage Encyclopedia
Language: English
Subject: Extraction of petroleum, Oil well, Wavefront Technology Solutions, Petroleum, Water injection
Collection: Petroleum Production
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Water injection (oil production)

Water injection or water flooding refers to the method in the oil industry where water is injected into the reservoir, usually to increase pressure and thereby stimulate production. Water injection wells can be found both on- and offshore, to increase oil recovery from an existing reservoir.

Water is injected (1) to support pressure of the reservoir (also known as voidage replacement), and (2) to sweep or displace oil from the reservoir, and push it towards a well.

Normally only 30% of the oil in a reservoir can be extracted, but water injection increases that percentage (known as the recovery factor) and maintains the production rate of a reservoir over a longer period.

Waterflooding began accidentally in Pithole, Pennsylvania by 1865. Waterflooding became common in Pennsylvania in the 1880s.[1]

Contents

  • Sources of injected water 1
  • Filters 2
  • De-oxygenation 3
  • Water injection pumps 4
  • Sources and notes 5

Sources of injected water

Any and every source of bulk water can be, and has been, used for injection. The following sources of water are used for recovery of oil:

Produced water is often used as an injection fluid. This reduces the potential of causing formation damage due to incompatible fluids, although the risk of scaling or corrosion in injection flowlines or tubing remains. Also, the produced water, being contaminated with hydrocarbons and solids, must be disposed of in some manner, and disposal to sea or river will require a certain level of clean-up of the water stream first. However, the processing required to render produced water fit for reinjection may be equally costly.

As the volumes of water being produced are never sufficient to replace all the production volumes (oil and gas, in addition to water), additional "make-up" water must be provided. Mixing waters from different sources exacerbates the risk of scaling.

Seawater is obviously the most convenient source for offshore production facilities, and it may be pumped inshore for use in land fields. Where possible, the water intake is placed at sufficient depth to reduce the concentration of algae; however, filtering, deoxygenation and biociding is generally required.

Aquifer water from water-bearing formations other than the oil reservoir, but in the same structure, has the advantage of purity where available.

River water will always require filtration and biociding before injection.

Filters

The filters must clean the water and remove any impurities, such as shells and algae. Typical filtration is to 2 micrometres, but really depends on reservoir requirements. The filters are so fine so as not to block the pores of the reservoir. Sand filters are a common used filtration technology to remove solid impurities from the water. The sand filter has different beds with various sizes of sand granules. The sea water traverses the first, coarsest, layer of sand down to the finest and to clean the filter, the process is inverted. After the water is filtered it continues on to fill the de-oxygenation tower. Sand filters are bulky, heavy, have some spill over of sand particles and require chemicals to enhance water quality. A more sophisticated approach is to use automatic selfcleaning backflushable screen filters (suction scanning) because these do not have the disadvantages sand filters have.

The importance of proper water treatment is often underestimated by oil companies and engineering companies. Especially with river-, and seawater, intake water quality can vary tremendously (algae blooming in spring time, storms and current stirring up sediments from the seafloor) which will have significant impact on the performance of the water treatment facilities. If not addressed correctly, water injection may not be successful. This results in poor water quality, clogging of the reservoir and loss of oil production.

De-oxygenation

Oxygen must be removed from the water because it promotes corrosion and growth of certain bacteria. Bacterial growth in the reservoir can produce toxic hydrogen sulfide, a source of serious production problems, and block the pores in the rock.

A deoxygenation tower brings the injection water into contact with a dry gas stream (gas is always readily available in the oilfield). The filtered water drops into the de-oxygenation tower, splashing onto a series of trays, causing dissolved oxygen to be lost to the gas stream.

An alternative method, also used as a backup to deoxygenation towers, is to add an oxygen scavenging agent such as sodium bisulfite and ammonium bisulphite.

Water injection pumps

The high pressure, high flow water injection pumps are placed near to the de-oxygenation tower and boosting pumps. They fill the bottom of the reservoir with the filtered water to push the oil towards the wells like a piston. The result of the injection is not quick, it needs time.

Water injection is used to prevent low pressure in the reservoir. The water replaces the oil which has been taken, keeping the production rate and the pressure the same over the long term.

Sources and notes

  • "New Billions In Oil" Popular Mechanics, March 1933—i.e. article on invention of water injection for oil recovery
  • Water injection
  • Waterflood Performance Predictive Calculations
  1. ^ Abdus Satter, Ghulam M. Iqbal, and James L. Buchwalter, Practical Enhanced Reservoir Engineering (Tulsa, Okla.: Pennwell, 2008) 492.


This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.