World Library  
Flag as Inappropriate
Email this Article

Naphtha launch

Article Id: WHEBN0021050015
Reproduction Date:

Title: Naphtha launch  
Author: World Heritage Encyclopedia
Language: English
Subject: Steamboat, Naphtha
Publisher: World Heritage Encyclopedia

Naphtha launch

A naphtha launch, sometimes called a "vapor launch", was a small motor launch, powered by a naphtha engine. They were a particularly American design, brought into being by a local law that made it impractical to use a steam launch for private use.

Naphtha launches

By the 1880s, the small steam engine was well established as a power unit for small steam launches, as well as for large boats. However US law, prompted by some past boiler explosions, required that all steam boats carry a licensed engineer at all times. Although this was no difficulty for a commercial craft, it prevented small steam launches being used for personal, recreational use. Becoming such an engineer required an apprenticeship of two years beforehand. One of the few amateurs to achieve this and to become their own engineer was Rosamund Burgess, wife of boat designer Starling Burgess.[1]

A more popular alternative was the naphtha launch, and its alternative power source to the steam engine.[2] Advertisements of the period used the deliberate phrase, "Every Man His own Engineer!"[3] to highlight this legal restriction.


The first naphtha launch appears to have been British, reported in the French journal Nature in 1888.[4] This launch, Zephyr, was the invention of Alfred Yarrow, a well-known builder of steam launches for some years previously. Similar launches were produced in the same year by the Swiss company Escher Wyss AG.[5] One of these was Alfred Nobel's graceful aluminium-hulled sloop Mignon, of 1892. Another, also of aluminium, was the Aluminia of 1894.

The first American naphtha launches recorded were those of the Ofeldt company of New York, who would later become well known as makers of naphtha engines.[5] They described this as the 'Essh' system, and may have been licensees of the Escher Wyss patents. As well as Ofeldt, complete launches were also offerd by the Gas Engine and Power Co. of New York. By 1890 they claimed to have sold over 500.[6]

Typical launches

The typical naphtha launch was an open launch of around 24' length. These were pleasure craft for use on fine weather excursions.[7][8] After all, a commercial boat with a professional crew would not have the regulatory problem that led to their invention. Naphtha launches appeared in the finest circles, in the best yacht clubs[9] and under the ownership of some celebrated names.[10]

Surviving examples

Few examples survive today. Some sources claim one,[11] others four.[12]

Naphtha engine

The naphtha engine is an external combustion engine, generally similar to the type of small steam engine already in use for steam launches. The working fluid is naphtha, which unusually is also used as a liquid fuel to power the boiler. Appearance is similar to a steam launch, having a small vertical boiler and vertical cylinders.

The burner for a naphtha engine uses naphtha itself, and is similar to that used for steam cars. Although such convenient and self-regulating liquid fuel burners were also used on steam launches, most launches at the time of the naphtha engine's heyday were still using solid fuel.

General arrangement

To avoid problems of premature condensation, the engine and boiler units were mounted together. Engines were three-cylinder single-acting vertical simple expansion engines, with 120° crankshaft spacing, so as to be self-starting without dead centre problems.[note 1]


The boilers were of spiral monotube form. These were single-pass water-tube(sic) steam generators, where liquid at one end of the tube boiled by the time it reached the end, without any looped circulation. Such boilers, although with conventional water and steam, were also used for steam cars such as the White. The boiler was mounted directly atop the engine, and encased in a polished brass or copper casing with a short funnel above. The purpose of the funnel was merely to vent fumes above the heads of passengers, rather than to act as a draught to draw the fire.


Unlike coal or wood, the jet burners used did not require additional draught.[note 2] The boiler was fired with a pressure jet burner, a small quantity of pressurised naphtha being tapped off from the boiler.[5] A prominent tube and funnel on the front of the boiler casing (sometimes mistaken for a whistle) is the air inlet. The fuel jet mixes with the downwards air flow in this vertical tube, then the mixed air and fuel is fed to a ring-shaped burner inside the boiler casing. For starting, a hand air pump was used to pressurise the fuel tank and encourage fuel flow, together with pre-heating of the burner coil by lighting a little of the fuel in a tray below it.[5]

There was no throttle valve or regulator to control the engine speed. As was commonly used on single-pass spiral monotube boilers, the burner output was regulated instead with the fuel valve and the boiler responded quickly enough for this to be sufficient.[13]


Lubrication of the engine was performed by the fuel itself, collected in a sealed wet sump arrangement beneath the crankcase. The naphtha fuel[note 3] was an acceptable lubricant and this avoided the problem of separating lubricating oil from condensed fuel vapour leaking past the piston ring seals. It did however require careful sealing of the crankcase.[5]

The engine valvegear was simple, compared to that of contemporary steam engines. A single rotating overhead camshaft ran above the cylinders, parallel to the crankshaft. Eccentrics on this shaft actuated a transverse slide valve for each cylinder. The valve camshaft was driven at engine speed[note 4] by gears from the crankshaft. A prominent handwheel on the camshaft allowed the engine to be reversed, in a similar manner to slip-eccentric valve gear by shifting the phase of the camshaft relative to the crankshaft.[5]


External water-cooled condensers were used, simple pipes run under the hull, along the length of the keel.[5] Despite the obvious risks of damage from grounding, these seem to have given little trouble in service. The fuel tank was in the fo'csle of the boat, well away from the engine and risk of fire. This fuel tank was pressurised by the returning naphtha, avoiding the need for a fuel pump.

Low boiling point

One of the attractive features that first led inventors to consider naphtha as a working fluid was its low boiling point, compared to water. This allows a relatively simple engine to be constructed, although it actually represents a limitation on the efficiency of such an engine. At the time, thermodynamics was already an advanced science and the limitations of thermodynamic cycles were well understood by physicists, if not by all engineers. By limiting the range of temperatures between which the engine worked, this actually reduces the potential efficiency of the engine, rather than increasing it.[14]

An earlier use of low boiling point fluids had been Du Tremblay's ether engine of the 1850s.[14] This was used for a bottoming cycle as an addition to a steam engine. Waste heat rejected through the condenser of the steam engine was used to boil ether and drive a second cylinder.

Other variants

Frank W. Ofeldt

Frank W. Ofeldt also designed the Alco Vapor engine, sold by the Alco Vapor Launch Co.[6] This burned kerosene and used alcohol (probably 'wood alcohol' or methanol) as a working fluid. This may have been a measure to avoid the Escher Wyss patents.

Later Ofeldt also designed a more conventional steam-generating water-tube steam boiler. This was similar to the "Lune Valley" pattern, a central drum surrounded by coiled water tubes, but with irregular wedge-shaped coils rather than a simple circle.[15]

'Simplex' engine

The "Simplex Naptha engine" built by Chas. Willard of Chicago was more akin to an internal combustion gas engine with timed spark ignition.[16] It is outside the scope of this article.

Hazards and explosions

Despite the obvious hazards and occasional reports of fires,[17] the naphtha launch appears to have worked reasonably well and safely.


The naphtha engine is not well known amongst model engineers, but at least one detailed reproduction has been constructed.[18]

In popular culture

In the 1921 novel of the popular "Tom Swift" series, "Tom Swift Among the Fire Fighters",[19] the hero escapes on a naphtha launch, describing it as "old-fashioned". The author also passes comment as to them being "a trifle treacherous" to light.[19]


This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.